Editing Register (section)

== Register ==
Is the process allowing to register your Asset in the blockchain trough images.

While being the lengthiest phase, you will only do it once in the life of the object. (caveat: you may do it more than once to care about object worn-out)

To do so, select "Register" in the "Burger" menu

=== Register "Generic" ===
The '''AssetId''' is a key component of your Asset management. This is the Name of your Asset in the BlockChain

Choose it wisely it cannot be changed once assigned in the BlcokChain (last step of Registration.

If the name you choose is reserved or is already existing, you will be notified and need to choose another one.

Once setup of your unique '''AssetId''' is done , the "Next" button will switch to a page asking to load a first picture. Make this picture a 'best shoot', it will stay as your reference picture.

{| class="wikitable"
!<div style="display: inline; width: 900px; float: right;">
[[File:768_-1_Register_Start_IMG_9363.jpg|100 px]] [[File:Arrow_Right_64_R.png|20 px]] [[File:768 -2 Register Assign AssetID IMG 9364.png|300 px]] [[File:Arrow_Right_64_R.png]] [[File:768 -3 Register Take first picture IMG 9284.png|300 px]] </div>
!You will need to assign a AssetId and it must be unique, if rejected because already in use you should use another name for it.
Once a good Asset Id is setup "Next" will show you a picture selector.

Either use an existing picture or use imbedded web camera with "Take Photo".
|}


=== Camera ===
Here using the internal camera, notice the "Flash" on and it's effect on the taken photo. 

'''Tips:''' 

''Use a Camera Apps like "Appollo Layer Camera" and take your 3 photos in advance, this apps allow to keep previous image and display it as a transparent 'layer' ensuring a better reproducibility of your images.''

'''Tips:'''

How to make [[good picture]]

{| class="wikitable"
!<div style="display: inline; width: 900px; float: right;">
[[File:768 -4 Register Camera Typical IMG 9341.jpg|300 px]][[File:Arrow_Right_64_R.png]][[File:768 -5 Register Camera Good Flash IMG 9344.jpg|300 px]] </div>
!Center the object and try to be as close as possible while staying sharp
In case of doubt always use Flash to normalize lighting condition.

|}


=== Learning phase: ===
Then you will be asked to take a second picture. Its purpose is select and optimized best set of '''Optical signatures'''.

Note:

This phase is not required for preset object (like "Banknote") as the best set have already been learned.
{| class="wikitable"
!<div style="display: inline; width: 900px; float: right;">
[[File:768 Register -6 Take Second picture IMG 9342.jpg|300 px]] </div>
!use the same framing and point of view as the previous one, and don't forget to setup the flash.
|}

=== '''Crop phase:''' ===
See your reference image and decide if the suggested area of interest is optimal (in case of doubt, leave it as is)
{| class="wikitable"
!<div style="display: inline; width: 900px; float: right;">
[[File:768 Register -6 Take Second picture IMG 9342.jpg|100 px]][[File:Arrow_Right_64_R.png|20 px]][[File:768 Register -7 Confirm Crop IMG 9346.jpg|300 px]][[File:Arrow_Right_64_R.png]][[File:768 Register -8 Learning IMG 9347.jpg|300 px]] </div>
!Optical signature will only de searched for in crop area, keep default, or restrict it if you have a good reason to avoid area which is too fuzzy, too wooly, overexposed or even change like a liquid.
|}

=== Proofing your set ===
A third image will be asked to verify that Signature set are made with good images. 

Once tested you either get a green message if the proofing is successful, and your reference image is good,

or you will get a yellow message with suggestion(s) to improve your set (most common errors are fuzzy images or missing flash)
{| class="wikitable"
!<div style="display: inline; width: 900px; float: right;">
[[File:768 Register -8 Learning IMG 9347.jpg|100 px]][[File:Arrow_Right_64_R.png|20 px]][[File:768 Register -9 Take Proofing Image IMG 9349.jpg|300 px]][[File:Arrow_Right_64_R.png|20 px]][[File:768 Register -10 Proof OK IMG 9352.jpg|300 px]] </div>
!again use the same format as the previous one, and don't forget to setup flash.
|}

=== Appropriation ===
Upon confirmation that the set is usable, time to 'mint it' (put it in the blockchain)
{| class="wikitable"
!<div style="display: inline; width: 900px; float: right;">
[[File:768 Register -10 Proof OK IMG 9352.jpg|100 px]][[File:Arrow_Right_64_R.png|20 px]][[File:768 Register -11 Appropriation Pressed IMG 9353.jpg|300 px]][[File:Arrow_Right_64_R.png|20 px]][[File:768 Register -12 Minting IMG 9354.png|300 px]] </div>
!Use the "appropriation" button to register it in the blockchain, then "Confirm" to ask for registration.
|}

=== Loading it in your Wallet ===

Once "Confirm" is pressed, it will call the wallet asking for approval of the transaction
{| class="wikitable"
!<div style="display: inline; width: 900px; float: right;">
[[File:768 Register -12 Minting IMG 9354.png|100 px]][[File:Arrow_Right_64_R.png|20 px]][[File:768 Register -14 Approve charge IMG 9355.jpg|300 px]][[File:Arrow_Right_64_R.png]][[File:768 Register -15 done IMG 9356.jpg|300 px]] </div>
!Here depicted is AppleId Wallet (GoogleID wallet have a similar UI)
Other wallet chosen during "Connect Wallet" phase have similar features.
|}

=== Optional 'Apple card' ===
you can keep an Apple Wallet card with information about your Asset,
{| class="wikitable"
!<div style="display: inline; width: 400px; float: right;">
[[File:768 Register -16 Card IMG 9357.jpg|300 px]] </div>
|}